Showing 49–64 of 129 results

Oxbow Renegade 1.0 Two-Way Radio


Oxbow Renegade 1.0 Two-Way Radio

Oxbow Renegade 2.0 Two Way Radio (Non Bluetooth Version)


Oxbow Renegade 2.0 2-Way Radio

Oxbow Renegade X Two Way Radio with Bluetooth® Wireless Technology


Oxbow Renegade X 2.0 2-Way Radio



Material: Urethane

Measurement: 19-3/4″ x 21-1/2″

Thickness: Minimum .130

Includes 18 stainless steel pop rivets for installation

Plow Shovels w/ Stainless Steel Shears (Set of 2) and Nose Guard


Plow Shovel Set w/ Shears and Nose Guard

Measurement: Approximately 10″ H x 32″ L each shovel

Material: 12 GA Stainless Steel (Shear), 10 GA Standard Steel Plate

Finish: Stainless Steel (Plow Shear and Nose Guard), Safety Yellow Powder Coat Paint

Includes: (2) Plow Blade, (2) Plow Shear, (18) 1/4-20 x 3/4″ Star Drive Pan Head Screws, (10) 1/4-20 x 2-1/4″ Stainless Steel Carriage Bolts, (12) 1/4-20 Stainless Steel Nylock Nuts, (2) 1/4″ Stainless Steel Washers

Plow Stainless Steel Shears (Set of 2)


SNO BLASTER Plow Stainless Steel Shears

As part of the SNO BLASTER plow shovels, the plow shears are the wearable part that after significant use will commonly need replacement.

Replacement on SNO BLASTER plow shovels only.

Measurement: Approximately 23-1/2″ x 1-1/2″

Material: 12 GA Stainless Steel

Finish: #4 Stainless Surface on leading side

Includes Hardware: (14) 1/4-20 x 3/4″ Star Drive Pan Head Screws

Polaris Snowmobile Tongue-Type Tow Hitch




SNO MASTER Rear Tow Hitch

SNO-MASTER Rear Hitch attaches quickly to the rear of the SNO-MASTER 48 and 72 Chassis using the included 4 – 1/4-20 x 7/8″ Stainless Steel Hex Bolts and 4 – 1/4-20 Stainless Steel Nylock Nuts. Each SNO-MASTER chassis includes the pre-drilled holes (some located behind the sticker) to attach the Rear Hitch on the left, right, or center of the groomed trail. The Stainless Steel Pin enables the 180 degree vertical movement needed to attach the Pin Coupler of the TRAKOR.

  • Material: Pin-Stainless Steel, Hitch-Carbon Steel
  • Finish: Bengal Black Powder Coated Paint

Reese 80305 Tow Ready Receiver Extension – 14″


Ring Coupler – 5″ Offset


Ring Coupler – 5″ Offset

Ring coupler used to connect towing machine to snow groomer.  The ring coupler allows for variable movement when linked to a Pintle Hook hitch. Includes a 5″ x 3/4″ rectangle tube offset to raise or lower the connection point.

  • Measurements – 3/4″ x 6″ (11 GA) + 3/8″ 2-3/4″ Ring
  • Finish – Bengal Black powder coated paint

Shear Nose Guard


Shear Nose Guard

Measurement: Approximately 6-1/2″ x 2″

Material: 12 GA Stainless Steel

Finish: #4 Stainless Surface on leading side

Shear Pin Upgrade Kit


Shear Pin Upgrade Kit

Upgrade your current Snow Groomers Hitch Plate and Coupler (Pin or Ring) with a 750 ft-lb. break rating. With the included 13/64″ drill bit, drill through the existing shear pin holes in both the coupler and hitch plate receiver then insert the new 3/16″ Zinc Yellow-Chromate plated Wire-Lock Shear Pin.

SLED Universal Hitch


SLED Universal Hitch

Fits most snowmobile rear bumper bars and many ATV rear bumper bars.  Easy to install, with no tools required and adjusts to fit 12-1/4″ to 20″ openings on bumper bars of 1″ up to 2-1/4″. Eliminate the side to side movement as seen with other bolt on hitches. Made of 10 GA steel plate and powder coated for long durability and rust protection. All hardware is made of stainless steel.  Connect your snow grooming equipment using the standard pin coupler included in all of our pin type groomer bundles.

Install Instruction Booklet

SM48 Drawbars (LH and RH)


SNO MASTER 48 Drawbars

Measurement: Approximately 1″ x 2″ x 82″

Material: 11 GA Standard Steel Rectangle Tube

Finish: Bengal Black Powder Coat paint

Includes: (1) Left Hand SM48 Drawbar, (1) Right Hand SM48 Drawbar, (2) .125″ x 1-15/16″ Stainless Steel Hitch Pins, (2) 1/2″ Zinc plated Washer

SM48 Hitch Plate Assembly


SNO MASTER 48 Hitch Plate Assembly

Measurement: 6-1/2″ x 8-1/4″

Material: 12 GA Carbon Steel Plate

Finish: Bengal Black Powder Coat Paint

Includes: (1) Upper Hitch Plate w/ Receiver, (1) Lower Hitch Plate, (4) 5/16-18 x 3″ Stainless Steel Carriage Bolts, (4) 5/16-18 Stainless Steel Nylock Nuts, (1) Anti-Seize Packet

SM48 Sub-Frame


SNO MASTER 48 Sub Frame

Measurement: Approximately 1-1/2″ x 14-1/2″ x 49″

Material: 1″ x 1-1/2″ 11 GA Rectangle Tubing, 7 GA Standard Steel plate

Finish: Bengal Black Powder Coat paint

Includes: (1) SM48 Sub-Frame, (4) 3/8-16 x 1-3/4″ Stainless Steel Hex Bolt, (4) 3/8-16 Stainless Steel Nylock Nuts