Showing 113–128 of 129 results

Tow Bar Short Tube

$50.00

Tow Bar Short Tube

Measurement: Approximately 1″ x 1-1/2″ x 12″

Material: Standard Steel Rectangle Tubing

Finish: Bengal Black Powder Coat paint

Includes: (1) 12″ Tow Bar Short Tube

TrailBlazer 20

$700.00

TrailBlazer 20

SnowGroomers.net’s newest addition Ultra Light Weight Snow Groomer to our narrow trail grooming drags is extremely light weight and can be towed by nearly any snowmobile.  Made from durable 1/2″ HDPE and 1/4″ ABS and has been tested to hold up to 200 lbs. of concrete pavers or blocks. Designed for quick and easy setup to set a compacted corduroy snow trail system.  Lots of folks want to build their own snow groomers. Often they want to save money.  This takes time and trial and error.  The TrailBlazer is meant so you can afford it and take a lot less time than building your own.  It is built to not rust or rot so it will last many years.

Recommended additional purchase – 4 to 6 (16″ x 16″ x 1″) concrete pavers or add 30-40 lbs of weight to the chassis for proper compaction and corduroy.

Note: Not recommended for

– professional or extensive snow trail grooming

– snow trail grooming over rough terrain with hidden hazards, such as large rocks, tree roots, or tree stumps.

TrailBlazer Cutter Plate

$80.00

TrailBlazer Cutter Plate

TrailBlazer Cutter Plate is used to precondition the snow covered trail in a similar corduroy pattern of the TrailBlazer comb.

Replacement part is pre-drilled to align and fit the TrailBlazer chassis.

TrailBlazer Swivel Coupler

$30.00

Trail Blazer Swivel Coupler

Designed to easily rotate 360 degrees to enable the TrailBlazer chassis to remain flat on the surface to enable proper grooming. Constructed of 1/8″ zinc plated mild steel with stainless steel hardware enabling rust resistance and durability for a long useful life.

Includes:

(1) 1″ Zinc plated drawbar swivel coupler

(1) 3/8″-16 x 2″ Stainless Steel Hex Head Bolt

(1) 3/8″-16 Stainless Steel Nylock Hex Nut

(2) 3/8″ Stainless Steel Flat Washers

NOT Included:

3/8″ Orange Handle Detent Pin

TrailBlazer XC 20

$700.00

TrailBlazer XC 20

Snow Groomers newest addition to our narrow trail grooming drags is extremely light weight and can be towed by nearly any snowmobile.  Made from durable 1/2″ HDPE and 1/4″ ABS and has been tested to hold up to 200 lbs. of concrete pavers or blocks. Designed for quick and easy setup to set classic cross-country / nordic ski tracks.

Recommended additional purchase – 4 to 6 (16″ x 16″ x 1″) concrete pavers or add 30-40 lbs of weight to the chassis for proper compaction and track setting.

Note: Not recommended for

– professional or extensive snow trail grooming

– snow trail grooming over rough terrain with hidden hazards, such as large rocks, tree roots, or tree stumps.

TrailBlazer XC 36

$900.00

TrailBlazer XC 36

Snow Groomers newest addition to our narrow trail grooming drags is extremely light weight and can be towed by nearly any snowmobile.  Made from durable 1/2″ HDPE and 1/4″ ABS and has been tested to hold up to 200 lbs. of concrete pavers or blocks. Designed for quick and easy setup to set classic cross-country / nordic ski tracks.

Recommended additional purchase – 4 to 6 (16″ x 16″ x 1″) concrete pavers or add 30-40 lbs of weight to the chassis for proper compaction and track setting.

Note: Not recommended for

– professional or extensive snow trail grooming

– snow trail grooming over rough terrain with hidden hazards, such as large rocks, tree roots, or tree stumps.

TrailBlazer XC Cutter Set

$40.00

TrailBlazer XC Cutter Set

TrailBlazer XC Cutter Set is used to break ice and hard packed snow from the area in front of the Track Molds prior to setting the Classic Ski Tracks.

TrailBlazer XC Track Mold

$40.00

TrailBlazer XC Track Mold

Each Track Mold is assembled from two separate parts.  1: Install the Track Mold bottom (1″ thick HDPE) using the included 5/16 hex bolts.  2: Apply Medium Black ABS Cement (Not Included).  3: Line up the pre-drilled holes of the Track Mold Cover and tighten with the included #10 Self-Tapping Screws.

TRAKOR Lower Weight Cushion

$30.00

TRAKOR Lower Weight Cushion

Material: .250″ ABS Plastic, Hair cell finish on outward side, smooth finish on inward side.

Measurement: Approximately 15-1/4″ x 15-3/4″

Includes: (2) Pre-installed strips of industrial double-sided adhesive tape.

 

TRAKOR Sled Skin

$50.00

TRAKOR Sled Skin

Material: HDPE

Measurement: 19-5/8″ x 26-1/4″

Thickness: Minimum .130

Includes: (14) stainless steel pop rivets for installation

TRAKOR Stainless Steel Cutters (Set of 2 – RH & LH)

$70.00

TRAKOR Stainless Steel Cutters

Measurement: Approximately 3-3/4″ x 1-1/4″ x 1-1/4″

Material: 10 GA Stainless Steel

Finish: Stainless Steel

Includes: (1) LH TRAKOR Cutter, (1) RH TRAKOR Cutter, (4) 5/16-18 x 3/4″ Stainless Steel Carriage Bolts, (4) 5/16-18 Stainless Steel Nylock Nuts

TRAKOR Track Mold (Set of 2)

$200.00

TRAKOR Track Mold

Material: Molded Urethane

Measurement: Approximately 15-3/4″ x 5″ x 1-3/8″

Includes: (2) TRAKOR Track Molds, (6) 5/16-18 x 3/4″ Stainless Steel Hex Bolts

UTV Universal Hitch 1″

$80.00

UTV 1″ Universal Hitch is made of 3/16″ Carbon Steel and finished with a durable Bengal Black powder coated paint.  The UTV 1″ includes a round hole to place a 1″ Bolt or Ball Hitch through to attach to the receiver of your UTV (with Tracks recommended), Snow Cat, or other towing device with a standard 2″ tow receiver.  The UTV 1″ Universal Hitch enables you to easily attach one of our three Pin Couplers. The UTV 1″ Universal Hitch includes a 5/16″ x 3-1/2″ Clevis Pin enabling 180 degree vertical movement.  Vertical movement of the UTV Hitch combined with the horizontal movement along the 3/8″ Orange Handle Detent Pin (Sold Separately) offers a smooth pull even over uneven snow pack allowing the snow grooming chassis to remain flat giving you a more even snow packed trail.

Voyager Dirt Bike Helmet Light Kit

$98.95

Wheel Kit Locking Pin

$20.00

Wheel Kit Locking Pin

Measurement: Approximately 3-1/2″ x 2″ x 3/4″

Material: Stainless Steel (Spring & Pin), ABS Plastic (Handle)

Includes: (1) 3/8″ T Handle Spring Loaded Pin Assembly